Designed to Scale

正在装载 40 节系统设计动画实验…

Designed to Scale — interactive system design course

Designed to Scale is an interactive system design course with 40 animated lessons. Each lesson is a 10-step simulation: you change one thing — add a cache, split a shard, add a replica, tighten a timeout — and watch P50 and P99 latency, throughput in req/s and CPU utilisation respond. Designed to Scale is built for engineers who learn by moving sliders instead of reading static diagrams.

What you get in the full course

Lessons40 lessons across 9 modules, about 11 hours of guided practice
FormatEach lesson is a 10-step animation with live P50 / P99 latency, throughput and CPU panels
TopicsRequest lifecycle, caching, sharding, replication, queues, consensus, failure and recovery, capacity planning, cost
RequirementsAny modern browser. No install, no backend, no account needed to read lesson 1
LanguageEnglish, with a full Chinese (简体中文) edition of every lesson
PriceLessons 1–2 free. The full course is USD 4.99 as a one-time payment
Updated2026-11-18

Why Designed to Scale is interactive

A system design book tells you that adding a cache lowers read latency. The course shows you where the hit rate saturates, how the miss path still hits the database, and what happens to tail latency when the cache is cold. Every lesson in the course keeps the numbers on screen, so the trade-off is something you observe rather than memorise.

The course starts with a single page load — DNS, connect, request, response — and adds one pressure at a time until you are reasoning about replicas, quorum reads and backpressure. Because each step is animated, you can replay a lesson, change a parameter and compare the two runs side by side.

Designed to Scale compared with static diagrams

Static diagrams show a correct design. Designed to Scale shows the cost of that design: the extra round trip, the queue that grows when a consumer slows down, the p99 that doubles when one shard gets hot. If you are preparing for system design interviews, the course gives you the numbers to defend a trade-off instead of repeating a pattern.

Who the course is for

The course is written for backend and full-stack engineers who can already ship a service but want to reason about latency and capacity before the incident review. It suits people preparing for system design interviews, engineers moving from a single database to sharded infrastructure, and anyone who has been told to “just add a cache” without being shown what that does to tail latency.

The course assumes you know what a request is and have seen a metrics dashboard. It does not assume cloud certification, a particular vendor, or familiarity with any specific framework. Every example runs in the browser, so a laptop with a browser is enough.

How a lesson in this latency lab works

Each lesson is a ten-step scene. Step one sets the baseline: a request, a server, a database, and the numbers you would see in production. Each following step adds one pressure — a cache, a second shard, a replica, a queue, a timeout — and the P50/P99 panel, the throughput counter and the CPU gauge update as the scene advances. Nothing is a screenshot; the numbers come from the simulation parameters for that step.

You can replay a step, pause on a graph and compare two runs. That is the whole point of an interactive system design course: you are meant to see the second-order effect, such as a cache that lowers average latency while raising the miss-path cost, or a replica that absorbs reads but returns stale rows for a few hundred milliseconds.

What you can measure after each module

Course outline

Nine modules, forty lessons: foundations and the request lifecycle; caching and invalidation; sharding and rebalancing; replication and quorum reads; queues, retries and idempotency; consensus and leader election; failure and recovery; capacity planning and headroom; and cost per request as traffic grows. Each module ends with a summary lesson that replays the whole pressure sequence.

If you only have ten minutes, start with lesson one: it follows a single page load hop by hop and shows exactly where the time goes. Lesson one is free and needs no account. The other thirty-nine lessons unlock with a one-time USD 4.99 purchase.

Latency numbers worth memorising

The course keeps returning to a small set of figures: a cache hit inside the same rack costs well under a millisecond, a cross-region round trip costs tens of milliseconds, and a cold cache turns the first request of every key into the slowest one. Shard skew matters more than average shard size, because the hot shard sets the ceiling for every write. Replica lag decides how long a read may return stale data, and a quorum read trades one extra network hop for a stricter guarantee.

Backpressure is treated as a design decision rather than an error: a bounded queue protects the consumer and raises rejection rate, an unbounded queue hides the problem until memory runs out. Retries need idempotency keys, and circuit breakers need thresholds measured under real load, not guessed. Each of these ideas appears in the interactive lessons as something you can move, not just something you read.

Pricing and access

The course is not a subscription. One payment of USD 4.99 unlocks all forty lessons for the account you sign in with, and progress is kept per account. Sign-in uses Google or a six-digit code sent by email, so there is no password to store. Refunds are handled by email within fourteen days of purchase.

Frequently asked questions

What is Designed to Scale?
It is an interactive system design course with 40 lessons. Each lesson runs a 10-step animation that shows latency, throughput and CPU usage changing as the architecture changes.
How much does the full course cost?
The full 40-lesson course is USD 4.99 as a one-time payment. Lessons 1 and 2 are free and the remaining 38 unlock after purchase.
Do I need to install anything?
No. Designed to Scale runs entirely in the browser; there is no install, no plugin and no local server.
Which topics does Designed to Scale cover?
Nine modules cover request lifecycle and latency, caching, sharding, replication, queues, consensus, failure and recovery, capacity planning and cost.
How is Designed to Scale different from a system design book?
A book shows static diagrams. Designed to Scale lets you change a parameter and watch P50/P99 latency, throughput and CPU utilisation move, so the trade-off is visible instead of described.
Can I use Designed to Scale for interview preparation?
Yes. The lessons are built around the trade-offs that system design interviews probe: caching, sharding, replication, queues and consensus.